ScienceQ Publishing GroupScienceQ Publishing Group
  • Home
  • Submit Manuscript
    • Open Access
  • List of Journals
  • Policies and Ethics
  • Contact Us

Construction and Installation of a Modern Display System Using Dot Matrix

HomeConstruction and Installation of a Modern Display System Using Dot Matrix

Research Article

Construction and Installation of a Modern Display System Using Dot Matrix.

Corresponding Author : Oladimeji Tolulope Tunji,

Department of Electrical-Electronic-Engineering, School of Engineering, The Federal Polytechnic, Ado-Ekiti, Nigeria

Email ID : tolulopett@yahoo.com

Received : 2019-01-12 Accepted : 2019-03-01 Published : 2019-03-01

Abstract : The LED dot matrix display is a display system which is used in information dissemination to larger number of audience within the location which it is situated. It has three sections; power, control and display. This which could be grouped into two main part; the hardware and software. The display system physically conveys set of programmed data on the controller card, the hardware part comprises of numbers of LED module, power supply module, controller card and the casing. The software part is the part on the controller card that stores the received programmed data. It uses a volatile memory which allows reprogramming and memory formatting for maximum of 1000times. The casing of the display system comprises of rectangular screwed and riveted aluminium rod, ACO Board and transparent plastic which covers it both in the front and back. The system switches on automatically whenever it is plugged to the AC Supply and it has a minimum efficient life span of 50,000hours and a maximum viewing angle and distance of 140degrees and 25metres.

Keywords : Display, Dot Matrix, Interface, Light Emitting Diode, Module.

Citation : Oladimeji Tolulope Tunji et al (2019). Construction and Installation of a Modern Display System Using Dot Matrix, J. of Advancement in Engineering and Technology, V7I3.01. DOI : 10.5281/zenodo.2580568

Copyright : © 2019 Oladimeji Tolulope Tunji. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Journal of Advancement in Engineering and Technology

ISSN : 2348-2931

Volume 7 / Issue 3

ScienceQ Publishing Group

Download Article

Reviewer Comments : Reviewers comments section of this article will get update shortly.

March 1, 2019
admin
Issue 3, JAET, Volume 7
No Comments
Submit Online
Article Structuring Guideline
Instruction for Author pdf
Policies and Ethics

 

pdf Copyright Form docx

Archives
  • JABZ
    • Volume 1
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 2
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • volume 3
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 4
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • volume 5
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • volume 6
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 7
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 8
      • Issue 1
  • JAET
    • Volume 1
      • Issue 1
      • Issue-2
      • Issue-3
      • Issue-4
    • Volume 2
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 3
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 4
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 5
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • volume 6
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 7
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 8
      • Issue 1
  • JALS
    • Volume 1
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 2
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 3
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 4
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 5
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 6
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 7
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 8
      • Issue 1
  • JBCE
    • Volume 1
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 2
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 3
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
  • JCLS
    • Volume 1
      • Issue 1
      • Issue 2
      • Issue 3
    • Volume 2
      • Issue 1
      • Issue 3
    • Volume 3
      • Issue 2
      • Issue 3
      • Issue 4
  • JMDDR
    • Volume 1
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 2
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 3
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 4
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 5
      • Issue 1
      • Issue 2
  • JPCS
    • Volume 1
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 2
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 3
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 4
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 5
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 6
      • Issue 1
      • Issue 2
      • Issue 3
      • Issue 4
    • Volume 7
      • Issue 1
      • Issue 2
      • Issue 3
  • Home
  • Submit Manuscript
  • List of Journals
  • Policies and Ethics
  • Contact Us
© ScienceQ Publishing Group 2023. All Rights Reserved.
SciencQ Publishing Group
Show Buttons
Hide Buttons
  • Home
  • Submit Manuscript
    • Open Access
  • List of Journals
  • Policies and Ethics
  • Contact Us